Throwing a lidded sugar bowl with a knob
A lidded sugar bowl is a rewarding vessel to make because it combines several core pottery skills in one useful form. Throwing the body teaches controlled wall pulling; trimming develops a steady foot; fitting a separate lid calls for accurate measurement. Add a knob and the result becomes a tactile object for the kitchen rather than a display piece.
Amelia Johannsen, a Barcelona-based ceramic artist, works with clay inspired by Pacific Northwest forests and the Mediterranean coastline. Her Amelia Johannsen's studio brings together functional pottery, sculptures and decorative plates, while its workshops introduce beginners to hands-on clay through relaxed sessions with wine and tapas.
The process suits Australia’s thriving studio culture. Sydney has neighbourhood pottery rooms, Melbourne is known for its laneway workshops, and Adelaide Central Market places handmade ceramics beside food and flower stalls. A completed bowl can feel at home on a breakfast bench beside a flat white or in a market display of locally made tableware.
The sequence below uses metric measurements and assumes access to a wheel, although the same principles can be adapted for a small electric kiln. Beginners should first master centring and wall pulling, giving each stage enough attention before moving to a complete lidded vessel.
Prepare your clay and workspace
Gather smooth, workable stoneware, a wire cutter, a metal rib, a needle tool, wooden trimming tools and calipers. For a bowl about 12 cm wide, prepare roughly 700 g of clay, then reserve 150 g for the lid and 30 g for the knob. Stoneware is forgiving for a first lidded form; porcelain demands tighter control and more even drying.
Wedge the clay until streaks and air pockets disappear, then shape it into a low cone centred on the wheel. Clean the wheel head before starting, and keep a damp sponge, small bowl of water and thin slip within reach. Wipe loose particles away because trapped grit can score a delicate rim. Before investing in an extensive setup, a quick skills assessment can help identify which techniques need more deliberate practice.
Centre the clay and open the base
Set the clay down firmly and squeeze it between your palms to anchor it. With elbows braced against your thighs, press inward near the base while keeping steady downward pressure. As the cone rises, cup your hands around it and refine the centred shape before the clay begins to wobble.
Use calipers to check that the base is centred, then open it with a rounded tool. For a 12 cm bowl, make the opening approximately 4 cm across and leave the floor 8–10 mm thick. Press the floor gently rather than digging it out, because thin patches are difficult to repair.
Pull the walls upward in two or three measured pulls, supporting the inside with one hand and the outside with the other. Aim for even walls about 5–6 mm thick and a cylinder roughly 12 cm wide and 8 cm tall. Stop while the clay is centred; a tall, thin wall is easier to collapse than to rescue.
Shape a balanced bowl
Once the cylinder is even, compress the rim with your fingertips and round it with a damp sponge. Use a metal rib against the outside while your other hand supports the interior, shaping a gentle belly rather than a straight tube. The finished rim should be about 11 cm across so the lid has room inside.
Keep the upper wall firm enough to retain its shape and the base sturdy enough to trim later. Check the rim from above and correct any oval area before the walls become leather-hard. A soft, even curve leaves space for sugar while giving the knob a secure overhead position.
Set the bowl upright on a board and let it firm beneath a loose cover. Rushing to shape a warm bowl can leave it lopsided, so allow the clay to become workable without becoming stiff and dry.
Throw a matching lid
Once the bowl is firm enough to handle without distortion, trace its mouth onto thin paper and cut out a template. Check the lid against this guide rather than judging it by eye. Leave about 1–2 mm of clearance at the fitting edge, since clay and glaze can change slightly during firing.
Centre the reserved clay and throw a short, wide cylinder about 12 cm across. Wire it off, place it upside down on a level bat and trim the flange to around 1–2 mm beyond the paper template. Hollow the underside into a shallow recess, then refine the top into a low dome while leaving the centre flat for the knob.
Allow the lid to become leather-hard, then test it in the bowl with a sheet of tissue protecting the rim. It should enter without touching the sides and sit without rocking. Trim a high spot from the underside if necessary, and make a tiny alignment mark before refining the fit further.
Attach a comfortable knob
Roll 30 g of the remaining clay into a smooth ball. Lightly score the flat area on top of the lid and the base of the knob, brush both surfaces with thin slip, and press them together firmly. Mark the knob’s front lightly so its orientation remains clear, then remove squeezed-out slip with a barely damp sponge.
Shape the attached knob into a compact dome, roughly 25 mm wide and 15 mm high. Keep it solid and rounded, with no thin stem that could chip. It should be large enough to grip with slightly damp fingertips but modest enough not to crowd the lid.
Let the join reach leather-hard before trimming the surrounding edges. If it opens as the pieces dry, score the cracked area, add a little slip and support the lid on a soft form. Avoid forcing misaligned pieces together, since that creates tension and encourages further cracking.
Trim, dry and fire the finished pieces
When the body and lid are bone dry, turn the bowl upside down on a bat and trim its foot. Cut a recessed foot ring about 5–6 mm wide, keeping the base 8–10 mm thick, then sand the underside level with fine abrasive paper on a wooden block. Remove all dust and confirm that the dry lid still clears the rim.
Dry the pieces slowly: cover them loosely for the first 24–48 hours, then leave them uncovered in a ventilated studio. Warm or humid weather will extend the process, so judge dryness by colour and weight rather than the calendar. Bisque fire according to the clay manufacturer’s limits, then glaze-fire only when every joint is sound.
Apply a transparent or satin glaze to the interior, leaving the lid’s seating edge and the foot free of glaze. A food-safe glaze suits the bowl’s purpose, while an unglazed knob offers a pleasant grip. Fit the glazed pieces once more before firing. When preparing work for an Australian weekend craft market, Creative Repertoire offers practical guidance on presentation, pricing and promotion.
Amelia’s workshops provide a practical way to experience the whole sequence, from centring clay to matching a lid and attaching its knob. They also offer the sociable format of a hands-on clay session paired with wine and tapas, suitable for curious beginners and experienced makers learning a new form.
Visit the studio website to explore available and sold work, follow Amelia on Instagram for current pieces, and subscribe to the mailing list for workshop dates and event news. Choose a session, reserve a place and start shaping your own sugar bowl at the wheel.