Build a Simple Kick Wheel from Reclaimed Wood
A kick wheel brings a slower, more physical rhythm to pottery. Instead of relying on a motor, the potter keeps the wheel head turning with a foot bar connected to a heavy flywheel. That steady movement can make throwing feel more deliberate, especially when working with small bowls, cups and sculptural forms.
Reclaimed timber is well suited to a home-built pottery wheel because the frame does not need to look polished. It needs to be stable, square and strong enough to resist vibration. Old hardwood shelving, sound fence rails, timber benches and salvaged flooring can all become useful components after careful inspection.
For Australian makers, this project suits a garage, covered patio or backyard studio in places such as Melbourne, Sydney or Brisbane. Allow space for clay splash, water buckets and drying boards, and remember that a wheel used in a rental property may need a floor protection mat to avoid marking concrete, tiles or timber.
Plan the wheel around your working height
A comfortable kick wheel usually places the wheel head around 45 to 55 centimetres above the floor, depending on your height and throwing posture. The seat should leave your knees slightly lower than your hips, while the kick bar should be easy to reach without twisting your back.
Measure the available space before cutting timber. A practical home model might have a base about 70 centimetres wide and 90 centimetres long, with the flywheel positioned beneath the wheel head. Keep the footprint broad enough to prevent rocking, particularly if the floor is smooth concrete.
Draw the frame from the side and above before buying hardware. Mark the locations of the wheel head, bearing blocks, seat supports and kick bar. This simple sketch will reveal collisions between your feet, the flywheel and the lower frame before you make permanent cuts.
Select and prepare reclaimed timber
Choose dry, straight timber without rot, insect damage, deep splits or excessive knots. Hardwood from old furniture can provide excellent strength, while construction pine is acceptable for bracing and non-load-bearing parts. Avoid timber that has a strong chemical smell or an unknown industrial history.
Old painted boards require special care. Lead paint may be present in older Australian homes, so avoid sanding suspect surfaces indoors and follow local health guidance for testing and disposal. Do not use old sleepers or treated pine for surfaces that may contact clay, water or skin unless you can identify the treatment and its condition.
Remove nails and screws with pliers, then brush away dirt before cutting. A thicknesser, hand plane or coarse sandpaper can flatten uneven surfaces. Seal the finished timber with a water-resistant coating, but leave the wheel head surface easy to clean. A few coats of hard-wearing polyurethane or marine varnish can help in humid coastal conditions.
Build a rigid base and upright frame
Construct a rectangular base from two long rails joined by cross members. Use exterior-rated screws and waterproof glue, then add diagonal braces if the frame flexes. Reclaimed timber often has old screw holes, so position new fasteners in sound wood and pre-drill to reduce splitting.
The upright supports should hold the bearing blocks in precise alignment. Build both sides together where possible, clamping them face to face before cutting matching holes. A misaligned shaft will create drag, wobble and uneven rotation, even when the frame itself feels solid.
A useful improvement is to make the bearing blocks removable. Bolt them to the uprights rather than permanently gluing them in place. This allows you to replace bearings, adjust shaft height or dismantle the wheel when moving house. Washers under the bolts can spread pressure across older timber.
Make the flywheel and drive system
The flywheel stores momentum between each kick. You can make one from a thick timber disc, several laminated boards, or a salvaged circular tabletop cut into a balanced shape. A diameter of 55 to 75 centimetres gives useful momentum without making the wheel excessively heavy.
Cut the disc carefully and check its balance by resting the shaft on two supports and allowing the wheel to rotate freely. If one side repeatedly drops to the bottom, remove a small amount of material from that area or add discreet counterweights to the lighter side. Smooth all edges and keep fingers away from the rim during testing.
Use a straight steel shaft with a diameter suited to the bearings you can source locally. Pillow-block bearings are convenient because they bolt directly to timber, while flange bearings can work in a compact frame. The wheel head and flywheel must sit firmly on the shaft, using collars, keys or locking hubs rather than relying on friction alone.
The kick bar can be a hardwood lever attached to a crank or offset point near the flywheel. Its travel should be smooth and low enough for your foot to push comfortably. Test the mechanism by hand first. Any sudden catch, side-to-side movement or scraping sound should be corrected before clay is added.
Fit the wheel head and finishing details
A wheel head between 25 and 35 centimetres wide is suitable for many beginner projects. A thick timber disc can work for early experiments, although a metal or laminated hardwood head will stay flatter over time. Secure it centrally and check its runout by holding a pencil close to the edge as it turns.
Add a shallow splash tray around the wheel head using sealed plywood, recycled plastic or a food-safe tub cut into two halves. The tray should lift off for cleaning. Pottery clay quickly settles into bearings and joints, so a removable design will extend the life of the wheel.
Before decorating the finished machine, make it practical. Rounded corners, sealed surfaces and a simple tool rack are more useful than elaborate trim. If your work includes carved vessels or decorative pieces, techniques such as these gold luster techniques can add a refined finish later, but the wheel itself should remain easy to wash.
Test safely and adapt it to Australian studios
Place the wheel on a level surface and test it without clay. Turn the flywheel slowly, listening for bearing noise and watching the wheel head for wobble. Increase speed gradually, then stop and inspect every connection. A loose shaft collar or shifting bearing can become dangerous once momentum builds.
Wear enclosed footwear and close-fitting clothing while testing. Keep hair, cords and loose sleeves away from the flywheel. Australian Work Health and Safety requirements apply to workplaces, studios and many community settings, so anyone using the wheel in a class or business should assess risks, maintain equipment and provide clear operating instructions.
Ventilation and water management matter in a home studio. Clay dust should be controlled with wet cleaning rather than dry sweeping, and slurry should not be washed into household drains. Let sediment settle in a bucket, pour off clearer water and dispose of the remaining clay according to local council guidance. This is especially important in dense areas such as inner Sydney or Melbourne, where plumbing and neighbours are close by.
Reclaimed materials can also keep the project affordable in the Australian second-hand market. Look at Gumtree, Facebook Marketplace, local tip shops and demolition salvage yards for timber, bearings and old steel. Hardware chains such as Bunnings can fill the gaps, while a local engineering supplier may provide a better shaft or bearing than a general-purpose home repair part.
Once the wheel runs smoothly, practise centring small amounts of clay before attempting large forms. Begin with cylinders, then move into bowls and altered vessels. A handmade kick wheel will have its own rhythm, and that character can become part of the creative process rather than a defect to eliminate.
Amelia Johannsen’s Amelia’s portfolio offers a useful source of visual inspiration for nature-led pottery, sculptural forms and decorative surfaces. Explore the work, follow the studio’s events and consider a hands-on workshop where clay, conversation, wine and tapas turn making into a shared experience.