A Drip Glaze That Evokes Melting Snow on Mt. Hood
Mt. Hood’s early spring snow does not vanish all at once. It clings to ridges, turns glossy in the sun and creeps downward in rounded rivulets. A successful white drip glaze copies that movement: a fluid layer over a dark ground, with bright edges and soft grey shadows rather than hard white lines.
The effect comes from chemistry, application and firing working together. A fluid base supplies the melt; clay thickness, wax resist, gravity and the heating curve decide where it stops. Functional ware also needs a well-fitted, food-compatible glaze, so controlled test tiles are safer than applying a new mix to a finished plate.
Amelia Johannsen’s nature-led ceramics provide a useful reference. The wider studio portfolio shows work shaped by Pacific Northwest landscapes and Mediterranean coastline references, while her Barcelona practice moves between pots, decorative plates, sculpture and abstract forms. The snowy cascade becomes a landscape rather than a decorative coating.
Australian makers commonly collect materials locally, share kiln time, test at home and sell through weekend craft markets or Instagram. Melbourne, Sydney, Brisbane and Perth all have active pottery communities, yet local kilns, bodies and clay chemistry differ enough that every recipe needs adjustment.
Start with a dark, mature body
Begin with smooth, iron-bearing stoneware or a commercial dark body. White glaze needs a dark field to reveal each rivulet, and the body must reach the same maturity as the glaze. Uneven water absorption can stall a run or encourage crawling, so avoid a heavily grogged body when you want a clean, continuous melt.
Bisque test pieces to the maker’s recommended temperature, usually around cone 06, and keep the bisque clean. Melbourne and Sydney potters often share kiln rooms, so ask the operator which body-and-glaze combinations have adhered well. Brisbane and Adelaide suppliers may offer different dark stoneware; record each clay’s cone range and shrinkage rather than treating its colour name as a specification.
Build a glossy snow base
Use a smooth, glossy base as the starting point. For a cone 6 oxidation test, mix by dry weight: 40 percent custer feldspar, 30 percent silica, 15 percent whiting, 13 percent EPK kaolin and 2 percent bentonite. The feldspar and whiting provide the melt, while silica and kaolin build the glassy matrix and bentonite helps suspension.
Blend the dry materials thoroughly, then add water until the slurry reaches a creamy, brushable consistency. Sieve out coarse particles and let the mix settle before testing. Australian pottery suppliers can vary in particle size and chemistry, so compare a small batch with a control tile from a familiar commercial glaze before scaling up.
Pure white keeps the effect crisp. A trace of cobalt carbonate can create blue-grey shadows in a separate trial, but only a food-contact-approved formulation should reach functional ware. Mark every container with the percentages, clay body, application thickness and firing position so the useful result can be reproduced.
Control the flowing edge
Apply two or three generous coats to the upper rim or raised area, building roughly 1.5–2 mm. Thick application supplies material for rounded drops, while the first coat anchors the surface. Leave the foot bare, wax the underside and place the piece on a clean kiln shelf with room beneath for overflow.
If the platter will hang rather than stand, build it as a wall piece from the start. The wall-art pottery guide explains how vessel shape, hardware and visual balance can work together; align the display orientation with the firing orientation so the glaze travels as intended. Vertical firing needs secure supports and an experienced kiln operator.
To stop a run, use wax resist below the chosen edge. A torn or lightly brushed resist gives a softer snowline than a ruler-straight one. Place it where a melt would pause beside a ridge or change in slope, leaving bare clay below so the white shape reads clearly against the dark body.
Fire for flow and fit
Fire first tests in oxidation to cone 6, or the temperature approved for the clay body, using witness cones rather than the kiln display. Cone 6 is roughly 1200–1225°C in many electric kilns, and a faster final ramp can increase flow. A short top-temperature hold changes the rivulets too, so compare it with a no-hold firing.
Place trial tiles near the top, middle and bottom of the kiln. Heat and load position can change viscosity enough to produce very different rivulets. Shared Australian studio kilns often mix several artists’ work, so label shelves, use a catch plate and tell the kiln technician about running glaze before loading.
Quicker cooling often preserves clear gloss, while a controlled slower cool may suit satin snow. Results can vary with kiln calibration and clay brand, so photograph a sample from every firing. That record is more valuable than chasing one dramatic run that cannot be repeated.
Test safety and Australian requirements
Test for pinholes, crazing, blistering and adhesion, then compare glazed and unglazed edges. Crazing is not automatically a defect, but it can stain and may suit food service poorly. A liquid-holding plate also needs checking where glaze thins over rims, because those areas may become weak.
For functional ware, use only materials identified by the supplier as suitable for food contact, and keep lead- or cadmium-bearing glazes off eating surfaces. In Australia, AS/NZS 2276.2 covers decorated ceramic tableware, while the Australian Consumer Law requires sold products to be safe and not misleading. Keep test records and label each piece as functional or decorative.
State and territory fair-trading rules also affect how a studio markets goods. A maker selling at a Melbourne weekend market, Sydney design market or Instagram shop should display accurate firing, care and food-use information. Follow the supplier’s safety data sheet, and use a P2 respirator and wet-cleaning methods for dry silica.
Refine, document and share
Once the melt is repeatable, adjust one variable at a time: glaze thickness, resist placement, top temperature or clay body. Photograph each tile beside its recipe card and compare the dried white edge with the fired result. A useful working formula includes percentages, clay brand, firing cone, kiln position and notes on gloss, run length and colour.
When the recipe is ready for company, a supervised workshop can make testing social. Check the pottery workshop calendar for Amelia’s clay events; Barcelona sessions pair the work with wine and tapas, fitting Australian BYO gatherings and booked weekend dates. If alcohol is sold rather than supplied as BYO, state and territory liquor-licensing rules apply.
Set out materials, ventilation and handling rules before guests arrive, and give each person space to glaze a test tile. The small tiles let the group compare thickness, flow and surface directly while everyone learns how the same formula behaves across different hands and kilns.
Make one small batch, fire three tiles and keep the recipe card with the results. Then explore available and sold pieces through Amelia Creations, follow the studio on Instagram, subscribe to the mailing list for workshop updates and join a hands-on clay session. Each action carries the same idea: controlled flow, a clearly recorded recipe and enough restraint for the white glaze to read as mountain snow.