Throwing a Large Vase: The First Thirty Pounds of Clay

A large vase begins long before its walls rise into a graceful neck. The first thirty pounds of clay are about preparation, rhythm and restraint: preparing a stable wheel, finding the centre, and learning how much pressure the material can accept. For a studio potter, this scale turns a familiar throwing process into a physical conversation with gravity.

Amelia Johannsen’s work brings together the earthy character of pottery, sculptural form and the changing patterns of nature, from the Pacific Northwest to the Mediterranean coastline. Her Amelia’s ceramic portfolio offers a useful glimpse into the relationship between thrown vessels, surface, and the landscape that informs them.

Reading the Scale of a Large Vessel

Thirty pounds is roughly 13.6 kilograms, a substantial mass even before water is added to the process. It is enough clay for a generously proportioned floor vase, a tall urn, or a broad sculptural vessel that may eventually stand on a plinth. The final object will weigh less after trimming and firing, but it will still demand careful handling at every stage.

A large vase is shaped by forces that become obvious as the walls rise. The clay wants to slump outward, the wheel head gathers momentum, and the form can begin to wobble if the base is too thin. A wide belly, narrow shoulder and extended neck must be planned as one continuous structure rather than a series of separate gestures.

For Australian homes, scale also has a practical side. A vase intended for a Melbourne terrace or a Sydney apartment may need a narrower footprint than one made for a spacious Brisbane entrance hall. Thinking about its eventual setting helps determine the proportions before the first lump touches the wheel.

Preparing Thirty Pounds of Clay

Start with clay that has an even moisture content throughout. A large lump with a dry skin or a soft centre will resist centring and may develop hidden weaknesses. Wedging on a sturdy plaster or timber surface removes air pockets and aligns the particles, while dividing the mass into manageable sections can reduce strain on the wrists and shoulders.

The wheel must be stable, clean and powerful enough to turn the load without losing speed. A large bat or plaster throwing surface gives the vessel room to spread, while a splash pan keeps water from travelling across the studio floor. Keep ribs, wire tools, trimming tools and a sponge within easy reach; stopping mid-process to search for equipment can interrupt the clay’s momentum.

Australian studios also need to account for climate. Dry winter air in Adelaide can stiffen exposed clay quickly, while Brisbane humidity may leave a thick form soft for longer than expected. A damp box, plastic sheeting and controlled ventilation help maintain an even drying rate between sessions.

Finding the Centre Without Fighting the Clay

Centring a large amount of clay is less about force than leverage. Brace the elbows against the body, keep the hands low and use the heel of the palm to compress the mass towards the middle. Short, controlled movements are more effective than pushing hard for too long, which can lead to fatigue and an uneven base.

Once the clay turns smoothly, open the centre gradually. Leave enough thickness beneath the floor to support the weight of the walls, particularly if the vase will have a broad belly. Compress the interior floor several times with a rib or fingertips, because a poorly compressed base can crack as the vessel dries.

The opening should be generous enough for the hand to work comfortably inside. With a large vase, a cramped opening makes it difficult to compress the floor, lift the walls evenly, or correct a developing bulge. The aim is a strong foundation that gives the form room to evolve.

Building Height Through Consistent Pulls

The first pull establishes the wall, but it does not need to achieve the final height. Lift slowly from the base, keeping the interior hand slightly ahead of the exterior hand. This supports the clay while encouraging it upwards rather than pushing it outward. Make several measured passes, removing excess water between pulls.

As the walls rise, pause to check the profile from different angles. A low viewpoint reveals sudden changes in thickness, while looking down from above helps identify whether the rim is becoming oval. Use a wooden rib or soft metal rib to refine the curve, but avoid overworking the surface once the structure is stable.

A large vase benefits from pauses. Letting the clay firm slightly under a loose plastic cover can make the next stage easier, especially when creating a shoulder or a tall neck. This is common in workshop settings too, where students learn that patience is part of throwing rather than a break from it.

Studio Checks Before the First Pull

Before adding height, make a quick practical review:

  • The wheel head and bat are secure.
  • The clay has an even, workable moisture level.
  • The base is compressed and thick enough to carry the form.
  • Tools, water and covering material are within reach.

During the lift, use a second set of checks:

  • Look for thinning at the lower wall.
  • Remove excess slurry before it weakens the clay.
  • Measure the opening and overall height regularly.
  • Stop if the rim begins to buckle or twist.

These small observations protect the vessel from avoidable damage. They also make the process easier to repeat, whether the vase is being made as a one-off studio piece or as part of a collection for an Australian gallery, open studio or makers’ market.

Finishing, Drying and Giving the Vase a Place

The rim deserves particular attention because it is the part viewers see and touch first. Compress it gently, soften sharp edges and decide whether the lip should remain crisp, folded, flared or slightly irregular. A natural variation can give the piece character, but an accidental split or thin section should be corrected before the vase leaves the wheel.

Large pottery must dry slowly and evenly. Cover the vase loosely, then uncover it in stages as the moisture leaves the clay. Avoid placing it in direct Australian sun or near a heater, even when the surface feels dry. The base and interior will usually retain moisture longer than the rim, so rushing the process can produce cracks.

Once leather-hard, the vase can be trimmed to clarify its weight and foot. After bisque firing, surface choices become part of the form: a quiet, sandy glaze may echo coastal stone, while layered marks can suggest bark, tide lines or weathered cliffs. Amelia’s notes on Mediterranean clay show how material origin can add another layer of meaning to a finished ceramic object.

A large vase also needs a considered destination. In Australia, buyers often want pieces that work with native branches, dried grasses or a simple eucalyptus arrangement, but an empty vessel can be equally powerful. At a local design market in Melbourne, a Sydney gallery or a Barcelona-inspired homewares setting, the object should have enough visual strength to hold its own without overwhelming the room.

Thirty pounds of clay can become a vessel with presence, but the real achievement is the sequence of decisions that makes it possible: preparing carefully, centring calmly, lifting with control and allowing the form to settle. Explore Amelia Creations’ available works, follow the studio on Instagram, or subscribe to the mailing list for pottery workshops, clay experiences with wine and tapas, and upcoming events.

Scroll to Top